Acti Q450 Handleiding

Acti Bewakingscamera Q450

Bekijk gratis de handleiding van Acti Q450 (2 pagina’s), behorend tot de categorie Bewakingscamera. Deze gids werd als nuttig beoordeeld door 34 mensen en kreeg gemiddeld 4.7 sterren uit 17.5 reviews. Heb je een vraag over Acti Q450 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/2

Q450 Multi-Imager Bullet Camera Quick Guide

This guide is for quick installing connecting the Q450 Multi-Imager Bullet Camera For more details, please refer and .

to the User s Manual. ’

Installation Notices

 This camera must be installed by qualiﬁed personnel and the installation should conform to all local codes.

 Do not replace batteries of the camera. Risk of explosion may occur if the battery is replaced by an incorrect type.

 To use an external power supply, please contact the camera manufacturer to conﬁrm that the power supply uses

the same power speciﬁcations as the camera. The power supply must comply with the LPS requirements.

All- -One Cable in

Cable

Deﬁnition

Remarks

RJ- 45

For network and PoE connections

Audio I/O

Green

Audio Out / Mic Out (Line Out)

Two-way audio transmission

Pink

Audio In / Mic In (Line In)

Alarm I/O

(5-pin Terminal Block)

Alarm In 2+

Alarm connection

#Do connect external NOT

power supply to the alarm I/O

connector of the IP camera.

Alarm In -

Alarm In 1+

Alarm Out -

Alarm Out +

Power (AC 24V)

(2-pin Terminal Block)

AC 24V 1

Power connection

AC 24V 2

microSD Card Slot / Default Button

T positions of microSD card slot and reset button are shown below. For details about how to detach the he as

camera’s front housing, please refer to section microSD Card Slot / Reset Button in the User’s Manual.

microSD Card Slot

Insert the microSD card into the card slot to store videos and snapshots. Do not remove the microSD card when the

camera is powered on.

NOTE: It is not recommended to record with the microSD card for 24/7 continuously, as it may not be able to

support long term continu s data read/write. Please contact the manufacturer of the microSD card for ou

information regarding the reliability and the life expectancy.

Reset Button

Press the reset button with a proper tool for at least 20 seconds to restore the system.

Camera Cabling

Please follow the instructions below for cable connections.

Power Connection

Please use an AC 24V adaptor and connect it to the 2-pin terminal block of the All- -One cable and the power outlet. in

Alternatively, connect the Ethernet cable to the -45 connector of the All- -One cable and plug the other end of the RJ in ,

cable to a Power Sourcing Equipment (PSE) switch.

Ethernet Cable Connection

Connect one end of the Ethernet cable to the - connector of the All- -One cable, and plug the other end of the RJ 45 in

cable to the network switch or PC.

NOTE: In some cases, Ethernet crossover cable might be needed when connecting the camera directly to the

PC.

NOTE: Check the status of the link indicator and the activity indicator LEDs. If the LEDs are unlit, please

check the LAN connection.

Green Link L indicates good network connection. ED

Orange Activity L ﬂashes for network activity indication. ED

NOTE: The ITE is to be connected only to PoE networks without routing to the outside plant or equivalent

description.

Before Login to the Camera

A client program will be automatically installed to the PC when connecting to the camera. Before logging in to the

camera, ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and plug-ins or

setting Internet’s security level to default. For further details, please refer to the User s Manual. ’

ActiveX Controls and Plug-ins Settings

Internet Security Level

Step 1: Start the Internet Explorer (IE).

Step 2: Select <Tools> from the main menu of the

browser. Then click <Internet Options >.

Step 3: Click the <Security> tab and select <Internet>,

and click <Custom level> to change ActiveX

settings.

Step 4: Set ActiveX controls and plug-ins items to “ ”

<Prompt> or <Enable>.

Step 1: Start the Internet Explorer (IE).

Step 2: Select <Tools> from the main menu of the

browser. Then click <Internet Options >.

Step 3: Click the <Security> tab and select <Internet>.

Step 4: Down the page, click Default Level and click “ ”

< > to conﬁrm the setting. Close the browser OK

window, and open a new one later for

accessing the IP camera.

V20200828

Camera Login

The default IP address of the camera is: 192.168.0.100. Therefore, to access the camera for the ﬁrst time, please set

the IP address of the PC as: 192.168.0.XXX; for example:

IP Address: 192.168.0.99

Subnet Mask: 255.255.255.0

 Key in the camera IP address on the URL bar of the web browser and hit Enter“ ”.

 For initial login, use the default username: admin“ ” and then setup the password. Follow the on-screen instructions

to do so. This username and password will be used for succeeding login. Note that the username and password

are case sensitive.

Default Username: admin Password: (user must set up first)

Install the ActiveX Control

 After connecting to the camera, the request for installing the ActiveX control will appear jus below the URL bar. t

 Right click on the information bar, and then click on <Install ActiveX Control > to permit ActiveX control …

installation.

 In the pop-up security warning window, click on <Install> to start downloading the software on the PC.

 Click on <Finish> after installation is completed.

Browser-based Viewer

The main page of the IP camera user interface is shown as the figure below. Please note that function buttons will

vary depending on the camera model.

Q450

Multi-Imager Bullet Camera

Quick Guide

Ver. 1.1

Product specificaties

Merk:	Acti
Categorie:	Bewakingscamera
Model:	Q450
Kleur van het product:	Wit
Soort:	IP-beveiligingscamera
Materiaal behuizing:	Metal, Plastic
Internationale veiligheidscode (IP):	IP66
Bluetooth:	Nee
Ondersteuning voor plaatsing:	Buiten
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Montagewijze:	Plafond/muur
Maximum resolutie:	5120 x 1440 Pixels
Totaal aantal megapixels:	4 MP
Videocompressieformaten:	H.264, H.265, M-JPEG
Diameter:	140 mm
Type stroombron:	AC, PoE
Minimale belichting:	- Lux
Aantal cameras:	1
Geïntegreerde geheugenkaartlezer:	Ja
Compatibele geheugenkaarten:	MicroSD (TransFlash), MicroSDHC, MicroSDXC
Ingebouwde HDD:	Nee
Nachtvisie:	Ja
LED-type:	IR
Vaste focale lengte:	2.8 mm
Video bewegings-detectie:	Ja
HTTPS-encryptie:	Ja
Audiosysteem:	2-weg
Aantal Ethernet LAN (RJ-45)-poorten:	1
Wachtwoordbeveiliging:	Ja
Omvang optische sensor:	1/1.8 "
Type beeldsensor:	CMOS
Password bescherming:	Gebruiker
Ruisonderdrukking:	Ja
Netwerkstandaard:	IEEE 802.1x, IEEE 802.3af
Lengte:	105.5 mm
Veiligheidsfunties:	Vandaalbestendig
Maximaal 30 frames per seconde:	30 fps
Ondersteunde netwerkprotocollen:	IPv4/v6, ARP, ICMP, IGMP, PPPoE, QoS, TCP, UDP, DHCP, UPnP, SNMP, SMTP, RTP, RTSP, HTTP, HTTPS, FTP, NTP, DDNS, IEEE 802.1X
IP-adresfilter:	Ja
Progressive scan:	Ja
Ethernet interface type:	Gigabit Ethernet
IK code:	IK10
Dag/nacht modus:	Ja
Aantal lenzen:	2
Maximum aperture number:	1.6
Controle camerapanning:	Nee
Kantelfunctie camera:	Nee
Aantal sensoren:	1
Videostreaming:	Ja
Weerbestendig:	Ja
Nachtkijker afstand:	40 m
Infrarood (IR)-afsluitingsfilter:	Ja
Aantal effectieve pixels (H x V):	2704 x 1568 Pixels
Wide Dynamic Range (WDR):	Ja
Wifi:	Nee
AC-ingangsspanning:	24 V
Bedrijfstemperatuur (T-T):	-40 - 55 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Kijkhoek lens, horizontaal:	180 °
Type waarschuwingsnotificatie:	E-mail
Ruisonderdrukkingstechnologie:	3D-ruisonderdrukking