Whirlpool YWMH53521HW Handleiding

Whirlpool Magnetron YWMH53521HW

Lees hieronder de 📖 handleiding in het Nederlandse voor Whirlpool YWMH53521HW (32 pagina's) in de categorie Magnetron. Deze handleiding was nuttig voor 62 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/32

MICROWAVE HOOD COMBINATION

INSTALLATION INSTRUCTIONS

This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. See the “Installation

Requirements” section for further notes.

These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration

in these installation instructions.

INSTRUCTIONS D’INSTALLATION

DE L’ENSEMBLE FOUR À MICRO-ONDES/HOTTE

Ce produit est conçu pour l’utilisation au-dessus d’appareils de cuisson électriques ou à gaz de 36 po (91,4 cm) de largeur ou moins.

Voir la section « Exigences d’installation » pour d’autres remarques.

Ces instructions d’installation sont valables pour plusieurs modèles. Il se peut que l’apparence de votre propre modèle soit légèrement

différente de celle montrée sur les illustrations dans ce document.

Table of Contents/Table des matières

W11496339A

MICROWAVE HOOD COMBINATION SAFETY ............................2

INSTALLATION REQUIREMENTS .................................................2

Tools and Parts .............................................................................2

Separate Cardboard Template .....................................................3

Location Requirements ................................................................3

Product Dimensions .....................................................................3

Electrical Requirements ...............................................................4

INSTALLATION INSTRUCTIONS ...................................................5

Remove Mounting Plate ...............................................................5

Rotate Blower Motor ....................................................................5

Locate Wall Stud(s) ......................................................................8

Mark Rear Wall .............................................................................9

Drill Holes in Rear Wall ...............................................................10

Attach Mounting Plate to Wall ...................................................10

Prepare Upper Cabinet ..............................................................11

Install Damper Assembly

(for wall venting only) ..................................................................11

Install the Microwave Oven ........................................................12

Complete Installation .................................................................13

VENTING DESIGN SPECIFICATIONS ........................................14

ASSISTANCE ................................................................................15

Replacement Parts .....................................................................15

Accessories ................................................................................15

SÉCURITÉ DE L’ENSEMBLE FOUR À

MICRO-ONDES/HOTTE...............................................................16

EXIGENCES D’INSTALLATION ...................................................16

Outillage et pièces ......................................................................16

Gabarit en carton séparé ...........................................................17

Exigences d’emplacement .........................................................17

Dimensions du produit ...............................................................18

Spéci cations électriques ..........................................................18

INSTRUCTIONS D’INSTALLATION .............................................19

Dépose de la plaque de montage ..............................................19

Réorientation du moteur du ventilateur .....................................19

Identi er la position du/des poteau(x) du colombage mural .....22

Tracé sur le mur arrière ..............................................................23

Perçage de trous dans le mur arrière .........................................24

Fixation de la plaque de montage sur le mur ............................24

Préparation du placard supérieur ..............................................25

Installation du module du clapet anti-re ux

(pour décharge à travers le mur uniquement) ............................25

Installation du four à micro-ondes .............................................26

Achever l’installation ..................................................................28

SPÉCIFICATIONS/CONCEPTION DU CIRCUIT

D’ÉVACUATION ...........................................................................28

ASSISTANCE ................................................................................30

Pièces de rechange ....................................................................30

Accessoires ................................................................................30

MICROWAVE HOOD COMBINATION SAFETY

INSTALLATION REQUIREMENTS

Tools and Parts

Tools Needed

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

■Measuring tape

■Pencil

■Masking tape or thumbtacks

■Scissors

■No. 2 Phillips screwdriver

■No. 3 Phillips screwdriver

for 1/4-20 x 3" (7.6 cm) bolts

■Drill

■3/16" (5 mm), 3/8" (1cm),

5/8" (1.6 cm) drill bits

■3/4" (1.9 cm) hole saw

■Diagonal wire cutting pliers

■Stud  nder

■7⁄16" (1.1 cm) socket wrench (or box wrench) for 1/4" x 2"

(6.4 mm x 5.1cm) lag screws

■11/2" (3.8 cm) diameter hole drill bit for wood or metal cabinet

■Keyhole saw

■Caulking gun and weatherproof caulking compound

■Duct tape

Parts Needed

For information on reordering, see the “Replacement Parts”

section.

NOTE: The hardware items listed here are for wood studs.

For other types of wall structures, be sure to use appropriate

fasteners.

NOTE: Depending on model, aluminum grease  lter and

charcoal  lter may be combined.

Materials Needed

Standard  ttings for wall or roof venting. See the “Venting Design

Speci cations” section.

A B C D E F G

A. 3/16-24 x 3" round-head

bolts (2)

B. 1/4-20 x 3"  at-head bolts (2)

C. Washers (2)

D. 3/16" toggle nuts (2)

E. 1/4" x 2" lag screws (2)

F. #6 x 3/8" Sheet metal screws (2)

G. Power supply cord bushing (1)

H. Damper assembly (for wall or

roof venting)

Not Shown:

■Mounting plate (attached to

back of microwave oven)

■Cardboard template (part of

packaging)

■Aluminum grease  lters

■Charcoal  lters (Depending

on model, charcoal  lters may

not be included. See User

Instructions.)

Separate Cardboard Template

The wall template and upper cabinet template is embedded in

the backside of the carton box. They are used as a rear wall

template and upper cabinet template.

1. Cut along the dotted line to separate the cardboard template

from the backside of the carton box.

2. Set the cardboard template to the side and refer to it during

the “Mark Rear Wall” and “Prepare Upper Cabinet” parts of

installation.

Location Requirements

Check the opening where the microwave oven will be installed.

The location must provide:

■Minimum installation dimensions. See the “Installation

Dimensions” illustration.

■Minimum one 2" x 4" (5.1 x 10.2 cm) wood wall stud and

minimum 3/8" (1 cm) thickness drywall or plaster/lath within

cabinet opening.

■Support for weight of 150 lbs (68 kg) which includes

microwave oven and items placed inside the microwave

oven and upper cabinet.

■Grounded electrical outlet inside upper cabinet. See the

“Electrical Requirements” section.

NOTES:

■If installing the microwave oven near a left sidewall, make

sure there is at least 6" (15.2 cm) of clearance between the

wall and the microwave oven so that the door can open fully.

■Some models have a pocket handle. If installing the

microwave near a right side wall, make sure there is at least

3" (7.6 cm) of clearance between wall and microwave oven

so you can grab the handle integrated inside the door.

■Some cabinet and building materials are not designed to

withstand the heat produced by the microwave oven for

cooking. Check with your builder or cabinet supplier to make

sure that the materials used will not discolor, delaminate, or

sustain other damages.

Special Requirements

For Wall Venting Installation Only:

■Cutout must be free of any obstructions so that the vent  t

properly and the damper blade opens freely and fully.

For Roof Venting Installation Only:

■If you are using a rectangular-to-round transition piece, the

3" (7.6 cm) clearance needs to exist above the microwave

oven so that the damper blade can open freely and fully.

See “Rectangular to Round Transition” illustration in the

“Venting Design Speci cations” section.

Installation Dimensions

NOTE: The grounded 3 prong outlet must be inside the upper

cabinet. See the “Electrical Requirements” section.

*30" (76.2 cm) is typical for 66" (167.6 cm) installation height.

Exact dimensions may vary depending on type of range/cooktop

below.

NOTE: To ensure good performance, do not obstruct top vent

air ow. If cabinets are deeper than 14" (35.6 cm) but no more

than 15" (38.1 cm), use the bump out mounting kit replacing the

I bar mounting plate from the wall. The bump out mounting kit

(part # W11185746) is not provided but can be purchased from

Whirlpool.

Product Dimensions

*Overall depth of product will vary slightly depending on door

design.

A. 2" x 4" (5.1 x 10.2 cm) wall stud

B. Grounded 3 prong outlet

12" (30.5 cm) minimum

14" (35.6 cm) maximum

30"

(76.2 cm)

minimum

A B

upper cabinet and

side cabinet depth

30"

(76.2 cm)

typical*

66" (167.6 cm) minimum

I bar mounting plate

Bump out mounting bracket

12" DEEPER 14" 14" DEEPER 15"

¹⁄₄

(41.3 cm)

¹⁄₈

(43.5 cm)

+/-

3/16

(0.5 cm)

17"

Up to

(43.2 cm)*

cm)

⁷⁄₈

" (76.0

A. Backside of the carton box

B. Cardboard template (including Rear Wall template and Upper

Cabinet template)

Product specificaties

Merk:	Whirlpool
Categorie:	Magnetron
Model:	YWMH53521HW

Heb je hulp nodig?

Als je hulp nodig hebt met Whirlpool YWMH53521HW stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Magnetron Whirlpool

Whirlpool MT 52 WH Handleiding

10 April 2024

Whirlpool WMCS7024PZ Handleiding

12 Maart 2024

Whirlpool GT 285 Handleiding

7 Januari 2024

Whirlpool AMW 735 IX Handleiding

6 Januari 2024

Whirlpool FT 391 Handleiding

5 November 2023

Whirlpool AMW 731 Handleiding

22 Oktober 2023

Whirlpool Ikea MBI A40 Handleiding

10 Oktober 2023

Whirlpool Ikea MBI S00 AL Handleiding

10 Oktober 2023

Whirlpool Framtid MW B00 S Handleiding

10 Oktober 2023

Whirlpool JT 479 SL Handleiding

20 September 2023

Handleiding Magnetron

Nieuwste handleidingen voor Magnetron

LG MC743D Handleiding

28 April 2024

Philco PMD 2085 BIB Handleiding

26 April 2024

Pelonis EM925AFO-P2 Handleiding

18 April 2024

LG MSER0990S Handleiding

17 April 2024

Electrolux EMS3067X Handleiding

17 April 2024

Samsung MG40DG5525AG Handleiding

16 April 2024

Sharp SMC1464KS Handleiding

16 April 2024

Sharp SMC1461KW Handleiding

16 April 2024

Electrolux LMS2173EM Handleiding

15 April 2024

Siemens HF85850 Handleiding

13 April 2024