Microchip MIC2111 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Microchip MIC2111 (35 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/35
MIC2111B
High-Performance, Multi- Mode,
Step- Down Controller
Micrel Inc. • 2180 Fortune Drive • Jose, CA 95131 • USA • tel +1 (408) 944 0800 • fax + 1 (408) 474 1000 • San - - http://www.micrel.com
October
13, 2015
Revision 2.1
General Description
Micrel MIC2111B’s is a programmable frequency, valley- -
current/voltage-mode PWM controller that provides the
control and protection features necessary for power
devices and drivers use current sensing across the that
inductor. The MIC2111B state can provide single tri- PWM
logic signal to work with either power stage modules or -
discrete driver The device has precision and MOSFETs.
enable and power functions for sequencing of -good (PG)
multiple power suppl In addition the solution ies. , is
compatible with intelligent power stages in a high-current,
step-down DC/DC converter.
To optimize system size and system efficiency, the
MIC2111B frequ ency can be programmed from 200kHz to
2MHz. The device operates in power-saving mode at light
loads by reducing udio rangefrequency. Optional outside a
operation the is possible when power-stage is configured
in light load mode. The solution uses different ial current
sensing for better current limit accuracy- and a dedicated
differential amplifier for remote output sensing for accurate
output voltage control. has a high The MIC2111B -gain
transconductance amplifier for loop compensation.
External slope compensation can added through be a
resistor to avoid sub-harmonic oscillations. Other features
include programmable OCP, output and thermal OVP,
OTP protections. The MIC2111B offers Micrel’s proprietary
bi-directional, single wire fault communication for total
system protection.
The MIC2111B 20-pis available in a in 3mm × 3mm TQ FN
package and has a junction temperature range of –40°C to
+125°C.
Datasheets and support documentation are available on
Micrel’s web site at: www.micrel.com.
Features
• Single 3.3V or 5V supply
• 4 Supports load currents up to 0A
• - -Programmable valley current/voltage mode PWM
architecture
• 3.3V logic PWM output compatible with power-stage
modules and DrMOS modules
• - Single tri state PWM output
• Programmable switching frequency: 200kHz to 2MHz.
• Differential remote sensing for output voltage and
inductor current
• ±0.6V reference voltage with total 1% accuracy for
output
• - - -Adjustable soft start/soft stop and pre biased safe
startup.
• Supports light load and outside audio modes
• Programmable slope compensation and loop
compensation
• - Enable input, power good (PG) output for sequencing
• Programmable OCP, OTP, and output thermal OVP,
dedicated FAULT pin for system safe startup/stopb
• Internal thermal shutdown and UVLO
• ° ° –40 C to +125 C junction temperature range
• - TQ Available in 20 pin 3mm × 3mm FN package
Applications
• Servers and work stations
• Routers, switches networking/telecom infrastructure ,
• Printers, scanners, graphics and video cards
• - High current, high performance POLs
Micrel, Inc.
MIC2111B
13, 2015 2 Revision 2.1
Typical Application
MIC2111B and DrMOS for a 2 A Synchronous Buck Converter5
Micrel, Inc.
MIC2111B
13, 2015 3 Revision 2.1
Ordering Information
Part Number Switching
Frequency
Junction
Temperature
Range
Current- Sense
Gain
Power
Stage Package Lead
Finish
MIC2111BYMT 200kHz to 2MHz − ° °40 C to +125 C 30V/V DrMOS 20-Pin
3mm × 3mm TQFN Pb-Free
Pin Conguration
20-Pin 3mm × 3mm TQFN (MT)
(Top View)
Pin Description
Pin Number I/O Pin Name Pin Name
1 I SLOPE
Valley Current Mode Slope compensation can be adjusted by adding a resistor from this pin to :
VIN (input power supply).
Voltage Mode: Artificial ramp controlled by SLOPE resistor
2 I EN Enable (Input): A logic signal to enable or disable the controller. The EN pin is CMOS
compatible. Logic high = enable, logic low = disable or shutdown. Do not leave floating.
3 I SEL Control Mode - Selection Pin: Connect this pin to AGND for valley current mode operation. -
Leave this pin open for voltage mode control operation.
4 I OVP Output OVP programming pin. Connect a resistive divider to set OVP.OVP pin has 0.6V
reference (see Functional Description for more details).
5 I FREQ Switching Frequency Adjust (Input): Connect a resistor from this pin to GND to set the
switching frequency.
6 I TJ Power Module Temperature Sense Pin. Connect resistor divider to program J comparator TJ. T
has 0.6V reference (see Functional Description for more details).
7 O PG Power Good (Output): Open n output, an external resistor to Vdrai OUT is required for pull-up.
8 I SS Soft-start pin for limiting inrush current. A resistor from this pin to ground sets the soft-start
time. If enabled, stop time is same as soft s -oft -start. Contact factory for soft stop.


Product specificaties

Merk: Microchip
Categorie: Niet gecategoriseerd
Model: MIC2111

Heb je hulp nodig?

Als je hulp nodig hebt met Microchip MIC2111 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Microchip

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd